
Product Name | SpeedyBee F7 V3 Flight Controller |
MCU | STM32F722 |
IMU(Gyro) | BMI270 |
USB Port Type | Type-C |
Barometer | BMP280 |
OSD Chip | AT7456E chip |
BLE Bluetooth | Supported. Used for Flight Controller configuration,built-in a single 2.4 GHz Wi-Fi-and-Bluetooth combo chip |
Flash FC Firmware Wirelessly | Supported. Please enter MENU > FC Firmware Flasher |
Download/Analyze Blackbox | Supported.Please enter MENU > Blackbox Analyzer |
DJI Air Unit Connection Way | Two ways supported: 6-pin connector or direct soldering. |
6-pin DJI Air Unit Plug | Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed. |
Flash(for BlackBox) | 500MB |
BetaFlight Camera Control Pad | Yes(CC pad on the front side) |
Power Input | 3S - 6S Lipo |
5V Output | 10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A. |
9V Output | 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A. |
3.3V Output | Supported. Designed for 3.3V-input receivers. Up to 500mA current load. |
4.5V Output | Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load. |
ESC Signal Pads | M1 - M4 on bottom side and M5-M8 on front side. |
UART | 5 sets(UART1, UART2, UART3, UART4(For ESC Telemetry), UART6) |
ESC Telemetry UART | R4(UART4) |
I2C | Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc. |
LED Pad | Used for WS2812 LED controlled by Betaflight firmware. |
Buzzer | BZ+ and BZ- pad used for 5V Buzzer |
BOOT Button | Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware. |
RSSI Input | Supported. Named as RS on the front side. |
SmartPort | Supported |
Supported Flight Controller Firmware | BetaFlight(Default),INAV |
Firmware Target Name | SPEEDYBEEF7V3 |
Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
Dimension | 41(L) x 38(W) x 8.1(H)mm |
Weight | 10.7g |
Product Name | SpeedyBee BL32 50A 4-in-1 ESC |
Firmware | SpeedyBee BL32 50A |
Configurator Download Link | http://github.com/bitdump/BLHeli/releases |
Continuous Current | 50A * 4 |
Burst Current | 55A(5seconds) |
TVS Protective diode | Yes |
Heat Sink | Yes |
External Capacitor | 1000uF Low ESR Capacitor(In the package) |
ESC Protocol | DSHOT300/600 |
PWM Frequency Range | 16KHz-128KHz |
Power Input | 3-6S LiPo |
Power Output | VBAT |
Current Sensor | Support (Scale=490 Offset=0) |
ESC Telemetry | supported |
Mounting | 30.5 x 30.5mm( 4mm hole diameter) |
Dimension | 45.6(L) * 40(W) * 8.8mm(H) |
Weight | 19.2g with heat sink |
Posted by Andy Clifft on 13th Feb 2025
Another master piece from the developers. Everything you would expect from Speedy Bee has been added to this amazing stack. I put this in my Mario 8" and it performs amazingly well. Highly recommended if your looking for performance & quality. Straight out of the box with no need to tune this thing will amaze you.
Posted by Unknown on 27th Jan 2025
This stack has lots of power and flexibility.
Posted by hans smets on 22nd Jan 2025
affordable, easy to install stack (on both 5 or 7 inch quad)
sufficient supplies delivered with the stack (cables, screws, ...)
stable bluetooth connection to make quick adjustments in the configuration
Posted by Alex on 5th Jan 2025
Excellent flight controller with motor control. Ivan support.
Posted by Alexander Kohlweg on 18th Oct 2024
Very good stack. Stable and smooth.
Posted by Yarnick on 2nd Sep 2024
Nice stack, I absolutely love the many connectors that speed up drone assembly
Posted by Arturas on 10th Aug 2024
Very nice stack, works very well . All pre plugs like dji could be more clear what uart number, but rest straight and clear. Look very high quality products. I would recommend
Posted by Alexander Kohlweg on 2nd Aug 2024
Best stack for copters. Support helped me fast and well through miseries i owned myself. Thank you Anna from Speedee Bee!
Posted by Patrick on 22nd Jul 2024
Kann ich nur weiterempfehlen super schnelle Lieferung, der Speedybee F7 habe ich jetzt schon drei mal bestellt und bin Super zufrieden. Auf jeden Fall Kaufempfehlung.