Flash your firmware 33% faster wirelessly + full FC configuration
Built with a better Bluetooth/WiFi 2-in-1 chip for 33% faster wireless data transfer. Update FC firmware with your smartphone in just 1 minute! Connect this FC via Bluetooth and fully configure any setting for Betaflight/Emuflight/INAV as you want.
Get your Blackbox data in 1 minute anytime, anywhere
With an optimized algorithm and upgraded Bluetooth/WiFi chip, you can dive into your Blackbox data every time you land your quad. Just take your smartphone out, connect, and download your flight in 20 seconds. The path to progress has never been easier.
Hate soldering? Just plug them all in!
It’s 2022, so having a plug vs soldering option is a must! Plug in your digital video transmitter, receiver, camera, VTX, and GPS to complete your build in no time. Also comes with 4x LED plugs so you can light up your quad with no headache. Prefer soldering? Just flip the board and start working on it.
Change your motor direction wirelessly
Finishing your latest build? Just replaced your motor after a crash? Take your smartphone out, and configure your motor direction wirelessly with the latest SpeedyBee app. Works for all BLHeli32 / BLHeli_S / BlueJay ESCs.
8 motors output, perfect for your X8 cinelifters!
There’s no other X8 flight controller better than this. Forget about crawling through your massive build just to plug in that USB cable. Just take out your phone to configure that X8 monster wirelessly before that challenging commercial shot. Professional FPV pilots got no time to waste.
Light up your quad in no time with 4x LED plugs
Need more visibility at night? Just plug in your LEDs and blaze the darkest trail you can find, no soldering required. With just one tap on the Boot button, you can cycle through all different LED presets* and pick the one you love!
*Or long press the boot button to switch to Betaflight LED mode
Forgot your LiPo checker? Just look at the FC!
Built with a 4-level LED battery indicator, now you can fly anywhere worry-free - even without your lipo checker!
32MB (typical FC memory) X 16 =500MB onboard Blackbox flash memory
Store up to 100 complete flights with our huge 500MB onboard Blackbox flash memory. Or keep your encrypted Area 51 files in it for your top-secret Man in Black mission. Whatever suits your tactical purpose.
*The Flash memory chip manufacture calculates the capacity by a rate of 1000(instead of 1024), so the display capacity on your computer will be slightly less than 500MB.
And packed with other useful features
● 9V 4A + 5V 2A individual BECs ● Power your GPS with a USB cable - no battery needed ● 22mm cutouts for FPV camera in your tight build ● Built-in barometer for accurate height calculation
SpeedyBee BL32 50A 4-in-1 ESC
50A ESC MADE FOR CHAMPIONS
When we say 50A, we mean it.
Real 50A output, ready for your baddest, meanest 6S motors. Blast through any obstacle during freestyle with no worry, or keep that highest throttle position during races.
The ESC is built with TVS protective diode to absorb the voltage spike when you plug in the battery, or during crashes that block your props. We also provide a humongous 1500uF low ESR capacitor, ensuring clean data from the gyro to the FC. Tested by 2 top racing pilots with both over 1500 packs, or you can put it to the test yourself.
Wanna crank it up to 128KHz PWM? Why not?
With F4 MCU, you can set the PWM frequency up to 128KHz. Find the best PWM frequency* to get for your build without any limitation.
* The ideal PWM frequency for each build varies depending on the frame, motors, props, and other factors. Higher PWM frequency doesn't necessarily means smoother flight. If the default 48KHz is not working for your build, you can increase the value gradually until you find the sweet spot. Check your motor temperature to avoid overheating.
CNC heat sink shield = no overheating in any condition
Built with high-quality CNC heat sink to significantly reduce the heat from your MOSFETs ensuring stable current flow at a high throttle position. Great benefit in a stylish blue finish.
Wiring Diagram Method 1 - Direct Soldering
SpeedyBee F7 V3 Flight Controller
USB Port Type
Supported. Used for Flight Controller configuration
Flash FC Firmware Wirelessly
Supported. Please enter MENU > FC Firmware Flasher
Supported.Please enter MENU > Blackbox Analyzer
DJI Air Unit Connection Way
Two ways supported: 6-pin connector or direct soldering.
BetaFlight Camera Control Pad
Yes(CC pad on the front side)
3S - 6S Lipo
10 groups of 5V output, three +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 6 +5V output included in the connectors on bottom side. The total current load is 2A.
2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 4A.
Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Used for WS2812 LED controlled by Betaflight firmware.
BZ+ and BZ- pad used for 5V Buzzer
Supported. [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked. [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.